[Scooter]F12 LC HIGH Hybrid ---> Italian Production[Project]

Lutzeddu ITALY

Well-Known Member
Hi guys, my name's Mauro and I'm from Italy, exatly from Sardinia!

I would introduce to You my Scooter&Project. It is a Malaguti Phantom F12 LC 2003.

The first Setup was...

Cylinder: Athena Sporting 70cc (like Stage6 Sport PRO)
Exhaust: Athena Sporting (like Stage6 PRO)
Crank Shaft: RMS Super Racing pen 10mm
Carb: Dell'Orto phbg 21mm
Air Filter: Malossi E14
Transmission: Malossi Multivar + Torque Drive
Clutch: Polini Evo 2G *
Shock Absorber: RMS 30 Regulation *

Here there are some photo of it

F123.jpg


F12Marmitta2.jpg


F12Ammortizzatore.jpg


F12RetroscudoIntagliato.jpg




A day I broke my motor so unluckly, and I decided to stop the scooter and make this Project!!! I would to do a scooter for underground street use, because I haven't the possibility to ride in a circuit...

This is the New Setup that I had think...

MECHANICS

Cylinder: Metrakit ProRace 2 70cc
Exhaust: Stage6 R1400
Crankshaft: Mazzucchelli Special Series pen 12mm

TRANSMISSION

Vario: Polini Evolution R02 101mm + Speed Drive Evolution 128mm
Belt: Evolution Kevlar
Clutch: Polini 2G Evolution
Bell: Koso/Stage6
Gear: Malossi Primary 13/44
Gear Box: Top Performances Nardò

ELECTRONICS

Ignition: Original (for the moment) + NGK Cable Racing IV

SAFETY

Shock Absorber: RMS 30 Regulation
Staple: Original Tuned
Discs: Braking Wave
Pads: Carbone Lorraine

MODS TUNED HANDCRAFT

Eliminated: System Electrical - Lights - Originals Tanks - Under Saddle - Chassis's Parts.

New Tank - Third Radiator - Carters Tuned - New Styling


I haven't write the components like Carb, Membranblock ecc... because now I'm not still sure of their. I put the description in the next days.


At the moment I haven't any pics, but is arriving the Transmission Evo and after the holidays I would buy new pics.

I had started the Project the week before, I coming to work on the chassis.
These mods are obvious, I had cut some parts from its.

Before...

TelaioNudo.jpg


TelaioZonaPosteriore.jpg


TelaioZonaRadiatori.jpg


TelaioZonaBloccasterzo.jpg


After...

TelaioNudoTagliato.jpg


TelaioZonaPosteriore2.jpg


TelaioZonaBloccasterzo2.jpg


TelaioZonaRadiatoriBassi2.jpg


Then I have made the support for saddle using this shelf's bracket

StaffaIntera2.jpg


StaffaIntera3.jpg


StaffaTagliata.jpg


StaffaFinita.jpg


StaffeFinite.jpg


StaffeFinite2.jpg



TelaioBlocco3.jpg


TelaioBloccoconSella.jpg


To attach the support I exploit this bracket of original tank

TelaioBloccodadietro.jpg


And now they are attached

StaffeSellasuTelaio2.jpg


StaffeSellasuTelaio4.jpg


SellaMontata2.jpg


SellaMontata6.jpg


TelaioBloccoeSella.jpg



After that I have eliminated some others parts to the chassis, some things that I haven't considereted so important!

CopiadiTelaioDettagliosupportiPedan.jpg


CopiadiTelaioZonaCentrale2.jpg


TelaioZonaElettronica.jpg



The chassis ready for the second step of cut

TelaioeBlocco5.jpg


And the final result

TelaioZonaCentraledopo.jpg


TelaioZonaPedanautlimata.jpg


DettaglioSupportoPedana.jpg


All the parts eliminated together

Immagine002.jpg



Here the scooter is coming to take features

Telaioconruote.jpg


TelaioconRuoteeCarena.jpg


And this is the F12

F12WIP.jpg


In the next days I will continue to work, I fit a third radiator back on front shield and tuned the careens.

I hope that You appreciate this topic, I will it open so You can say opinion about my scooter during the W.I.P

Bye Bye (Ciao)
 
Last edited:
Advertisement - register to remove this

Hi guyzzz, Today a friend have selt me the Membranblock Malossi VL14...
So some photos of pics that I have at the moment...:p

PezziDentro.jpg


PezziFuori.jpg


Pezzi.jpg



The Shock Absorber RMS 30 Regulation

AmmoRMS.jpg


AmmoRMSvalvola.jpg


AmmoRMSregistroritorno.jpg



Clutch Polini2G Evo

FrizionePolini2G.jpg



Membranblock Malossi VL14

PaccoLamellareMalossiVL14.jpg


VL14.jpg


Byeee
 
hmm this is so unlucky-I have been on Sardinia (north) 4 times.... and I absolutely could not find there no nice scooters-so here I see that there exist some :)
 
pavel.tenista said:
hmm this is so unlucky-I have been on Sardinia (north) 4 times.... and I absolutely could not find there no nice scooters-so here I see that there exist some :)

Hi, yes here in Sardinia the Scooter Tuning aren't so popular, especially in the North!!! I live in the centre, but at the South there is some Scooter that is very very good.
Maybe I can post any photo...

In these days I will UPDATE the Thread. I'm waiting the Transmission Evolution... 9||6

Ciaooo
 
hoi:)

nice scoot
I come from germany and i am go this year to sardegna,i was 12nd in sardegna
where do you come from sardegna(city)

sorry for my special english:p

CiaO

P.S.do you have icq???
 
DOMINIK. said:
hoi:)

nice scoot
I come from germany and i am go this year to sardegna,i was 12nd in sardegna
where do you come from sardegna(city)

sorry for my special english:p

CiaO

P.S.do you have icq???

Hi, my city is Nuoro, in the centre of Sardinia:)
Also my English isn't so right!!!

I don't know what is ICQ, but if You want contact me, use MSN Messenger. My email is: lutzeddu@msn.com

Ciao
 
Ehi, in these days I have adapted the Third radiator back on front shield.

ZonaRadiatoresuperiore.jpg


This is the original LC system

ImpiantoLCOriginale.jpg


And this is the Radiator deriving from Aerox/Nitro

RadiatoreNitroCompleto.jpg


So I had decided to adapt this components following the next paint :) and I use the "little tank" of F12 (sorry for my bad English...) The nozzle crossed in violet must be closed!!!

SchemaMontaggioterzoradiatoresullF1.jpg


VaschettaF12.jpg


Ok, using these slabs I have made the support for Radiator

PiastreperStaffeRadiatore.jpg


After...

StaffeRadiatoreNitro.jpg



Here are attached

StaffeRadiatoremontate.jpg


And with Radiator

RadiatoreMontato.jpg


RadiatoreMontato2.jpg



The nozzle for input the LC on the Radiator with the "little tank" is smaller than the output of F12, So I have put piece of tube around the nozzle to increase its external diameter and connected it to the little tank of F12 with a piece of normal LC tube. I hope that You understand this ;)

UgelloRadiatoreimboccolato.jpg


RadiatorevaschettaF12.jpg


F12LC.jpg


Then I had to modified the backshield to put out the minitank...

Retroscudo.jpg


ForoperVaschetta.jpg


Vaschettainposizione.jpg


In these photos You can be how i had connected together the 2 system

LC2.jpg


LC1.jpg


And at the end all the work completed, but there aren't attached the original Radiators of F12

ImpiantoLCOK.jpg



Today I hope that arrive the Transmission evolution, I'm waiting...

Ciaoooo
 
hey nice project!
i strongly advise you to get a competition ignition, my friend just got a mk pr2 on his am6 gearbike with the standard ignition, on low revs (half throttle) bike goes very bad but once full throttle bye bye, the bike flies...
at least you should get an unrestricted cdi for the moment so that you can get high rpms so that you can feel the power of the pr2...
 
Mr.Aerox said:
hey nice project!
i strongly advise you to get a competition ignition, my friend just got a mk pr2 on his am6 gearbike with the standard ignition, on low revs (half throttle) bike goes very bad but once full throttle bye bye, the bike flies...
at least you should get an unrestricted cdi for the moment so that you can get high rpms so that you can feel the power of the pr2...

Hi, I know that the standard ignition is so bad with these components, but at the moment I haven't €€€ to buy a Malossi Selettra or any other... I had think at an unrestricted CDI, but I haven't found any parts :? Can You suggest me some part???


However, the last Friday is arrived this package...

PaccoTrasmissionePoliniEvolution.jpg


PaccoAperto.jpg


9||6 9||6 9||6 Transmission Polini Evolution 9||6 9||6 9||6

TrasmissioneinScatola2.jpg


Vario EVO R02 101mm Components

ComponentiVariatoreEVOR022.jpg


Back Pulley 128mm Components

ComponentiPuleggePosterioriEvolutio.jpg


All the Transmission :winner:

TrasmissionePoliniEvolution2.jpg


Some particular...

VariatoreEVOR02fronte.jpg


VariatoreEVOR02retro.jpg


VariatoreEVOR02pisterulli.jpg


PiattelliVariatoreEVOR02.jpg


PuleggePosterioriEVO.jpg


PuleggePosterioriEVO4.jpg



These parts aren't buy new, buy they are so good!!! also if the belt is so consumed.
I can say that I have realized a little dream :W because I want these components by 1 year.

Ciaooo
 
p-mOe said:
very nice parts, i like your scoot, because an tuned f12 you can´t find very often!

go on, stay tuned!

patrick

Ehi, thanks for compliments! Now I'm tuning the careens in many parts, in these days I show You all the work:p

Moreover I have decided the components like Carbs, Air Filter, ecc... at 90%, I must only confirm their. Then I explain all here:)

Ciaoooo
 
alex89 said:
Madò Lutz anche qui a spammare ... lol ..

Great work ! Continua così ..

Bella Alex, essì spacco le balle anche qua<]

Hi Guyzzz UPDATE about careens, some mods...

Sottopedanaprima.jpg


Sottopedana.jpg


Sottopedanatagliato.jpg


PartiSottopedana.jpg


Sottopedanaprofilomodificato.jpg


Sottopedanaprofilomodificato2.jpg


Sottopedanamontato2.jpg



Before...

ZonaCentraleprima.jpg


After...

ZonaCentraledopo.jpg



ZonaGocciasxmontataprima.jpg


ZonaGocciasxprima.jpg


Work in Progress...

Retroscudodopo2.jpg


And Finished, I have made some correction with putty

Gocciadxfinita.jpg


Gocciasxfinita.jpg


ZonaCentralefinita.jpg


DettaglioGocciadx.jpg


DettaglioGocciasx.jpg



Then I have started to mods the backshield

RetroscudoWIP.jpg


Retroscudodopo.jpg


Retroscudodopo2.jpg


Retroscudodopomontato.jpg


Retroscudodopomontato2.jpg


It is to complete...


Now I would buy the GT, Carbs, Air Filter and after some days also the Crankshaft, stay tuned:W

However I work for others thing like petrol tank.

Ciaoooo
 
Back
Top